How To Remove A Pool Ladder

Initially we thought of creating a split guide to installing the South.R. Smith Puddle Ladders and the Due south.R. Smith Pool Rails. Just every bit we went deeper into the documentation, nosotros discovered that installing a puddle track is basically the same as installing a puddle ladder, so instead of creating different guides for basically the same thing, we've put together an all-in-one guide to installing puddle ladders and pool runway!

Tools Needed to install puddle rails and ladders

• Cadre drill four" or 5" diameter, depending on the size of the required anchor
• Adjustable wrench to tighten/loosen bolts
• Store-vac or pipe cleaner
• Epoxy/Compression Cement

Replacing Existing pool track and ladders

Irresolute out your existing ladders and pool rails to the new South.R. Smith Stainless puddle ladders and pool rails is pretty straightforward. In fact, all you need is a record measure out to mensurate out your existing equipment and so that you lot tin can option the correct model replacement and a wrench to remove the existing bolts.

How to determine the perfect replacement

Yous will need to take four (4) measurements to make up one's mind the perfect replacement for your pool rail and ladders.

• Width Dimension
• Center Dimension
• Acme Dimension
• Anchor Altitude

The figure above shows yous how to get the proper measurements, and one time y'all have those measurements, all you need to practise is pick the right blueprint for you and place your order! One time your new runway as arrived, simply remove the existing ones past taking out the bolts, aligning the new runway with the existing anchors, bolting them in, and you lot're done!

For more information on which rails can exist used for which dimension combination, check out the Southward.R. Smith Rail ID Guide hither.

For Ladders, all you need to do is select the aforementioned number of steps then replacing your existing ones should be quite straightforward.

Retrofitting S.R. Smith Handrails or Ladders to an Existing Deck

Now if yous don't have whatever handrails or ladders yet and you desire to retrofit i, then suspension out the tools and let's become started!

• Selection the desired design and wait for your order to arrive.
• Bank check the included anchor and drill the advisable hole for the anchor type. (iv" diameter for standard stainless steel or bronze anchor, or five" diameter for a universal anchor plus an extra ½" deeper than the ballast depth.
• Later drilling the hole, ensure that the hole is dry and dust-free. Suck out all of the dust with a shop vac and wipe make clean with a damp rag earlier assuasive it to dry off.
• Ensure that the drain pigsty at the bottom of the ballast is not plugged to allow any moisture to properly bleed away and to prevent corrosion.
• Gear up anchor flush on the deck with the wedge oriented AWAY from the puddle.
• Following your local construction code, bond the anchor to the existing rebar in your deck.
• Apply compression cement with a minimum of 3,000 PSI or epoxy and allow the cement/epoxy to cure properly according to manufacturer's instructions.
• After the cement or epoxy has cured, yous tin can now mount the rail or ladder on to the anchor.

Installation instructions for new pools.

Much like retrofitting to an existing deck, installation is pretty straightforward.

• Set anchor flush on the deck with the wedge oriented AWAY from the pool.
• Following your local structure code, bond the ballast to the existing rebar in your deck.
• Use compression cement with a minimum of 3,000 PSI or epoxy and allow the cement/epoxy to cure properly according to manufacturer's instructions.
• After the cement or epoxy has cured, you can now mount the rail or ladder on to the anchor.

With a few measurements, you can be easily on your way to enjoying your new pool ladders and pool rails from S.R. Smith. As you can run into from the instructions, installation is quite straightforward and DIY-Friendly! For a wait at what's available, check out our pool ladders and rails collections folio here.

Source: https://www.mrpoolman.com.au/blogs/news/easily-install-or-replace-your-pool-ladders-and-rails

Share this post